Oxballs Shockballs

The Oxballs Shockball

Vendor: Ballistic Metal

Construction

Like all ball crushers the Shockballs has two plates measuring 189x129mm. The lower one is made out of 6mm thick black acrylic, the top one out of 5.5mm thick clear acrylic. In the upper half, there is a hole in each plate. The lower one of the entire junk, the upper one for just the dick. Both holes are nicely rounded and flawlessly deburred so there will be no unintended pain or injuries. To fit most dick and ball sizes, the Shockballs comes in three hole sizes: 31.7mm & 44.5mm, 38mm & 51mm and 44.5mm & 57.5mm which I have bought.

The plates are connected by a clear acrylic hinge at the top. At the bottom there are two M5 screws for pressing the top plate down on the balls using wings nuts. On the screws there are also nuts as an adjustable compression limiter.

Detail of the Electrodes‘ Upsight with the 4mm Sockets

Below the holes there are two aluminums clamps screwed onto the clear acrylic using three sleeve nuts. The nuts’ round-head are the contact points of the electrodes. To connect the electrode with the power box, there are 4mm holes to fit banana plugs drilled into the bottom of the clamps.

Playing with the Shockballs

The hinge is a blessing and a cruse: Usually with ball crushers your fiddle with two or even three pieces, always risking to pinch some skin. This won’t happen with the Shockballs. But: If the sub already has a full-grown boner it is almost impossible to get the dick through the designated hole so the crusher can’t be closed again. The hinge’s height also limits maximum squeeze to 18mm (and a minimum of 42mm). While that is enough for a strong compression feeling, it won’t cater to the total nut pain pigs who want their balls compressed paper thin.

Detail of the Electrodes‘ Contact Areas

So much for the bad news. The good news is: The toy as an awful lot of fun to play with. While yes, putting it on with a hard dick, especially larger ones, not having to deal with shifting, getting wedged plates made me use the Shockballs way more often than my other ball crushers – even just for crushing. On a more personal note, I also like the industrial look of the brushed aluminum clamps compared to the poles being on the base plate on other e-stim ball crushers which then feature clear top plates. Tough some testees did not like the somewhat obstructed the view on the compressed sack.

The e-stim sensation is generally starts out mostly smooth. But since there are only three contact points it quickly can be turned stingy when the intensity is increased. Since the contact area and mass on both poles is almost identical, the sensation is felt on both poles when connected to one channel of the power box. The most interesting/ deviant stimulation is putting a mass-rich counter pole (everything up from the E-Stim Systems Torpedo Large like the Stuffer or [X]L Black Collection) inside the sub so the stimulation is only felt at the balls. Then choose a program which alternates between the two channels (like HiFreq on the Erostok ET232) so the agony constantly jumps from one side to the other.

Detail of the Screws to Tighten the Crusher

It is general a good idea to put a flexible cockring around junk’s base to keep the balls from retracting back into the body. If a sub has smaller/ tighter balls, I also recommend to stretch his nuts with one of the many flexible cock rings/ ball stretchers from Oxballs. This way they won’t be squeeze through the dick or junk hole (whichever has more slack). If you are really mean, you use the Zapp or Volt to electrify also the ball’s neck.

Conclusion: Nicely looking, easy to handle e-stim ball stretcher – if the dick is soft.
Pros Cons Where to get Price
Easy to put on and comfortable to wear Balls’ compression is limited by hinge height Ballistic Metal $114.95
Quality electrodes
Difficult to put on when dick is already hard
Tagged , , , . Bookmark the permalink.

Schreibe einen Kommentar

  • 9ee6292c41ad2ef691c9e90a8a7a2b8a

    9ee6292c41ad2ef691c9e90a8a7a2b8a